topic Re: Reshaping Zones in Modeling

Reshaping Zones

Anonymous — Wed, 31 Jan 2007 20:39:48 GMT

We have serveral zones in a file that we need to reshape and I cannot get the corner handles to appear or grab the side of the zone. When we originally inserted the zones we were able to reshape them at these points. Is there a preference or zone setting that I am missing or might be turned off? Any help would be greatly appreciated.

Thanks,

Brian

Re: Reshaping Zones

Anonymous — Thu, 01 Feb 2007 06:47:59 GMT

Hi Brian,
It sounds like you need to adjust the settings in your Model View Options to make the adjustments and then set them back.

Go to Document / Model View Options /
Verify which one you are using and on the very bottom right corner set the background fill of the Zone to display.

Re: Reshaping Zones

Chazz — Thu, 01 Feb 2007 14:28:32 GMT

If the zone shape was auto generated by clicking in a room, it is linked to that room. The only way to resize it is to move the walls and run a zone update. However, if you change the geometry method to manual (see below) the zone becomes editable using the standard polygon metaphors.

Re: Reshaping Zones

Anonymous — Sat, 03 Feb 2007 18:46:51 GMT

Thanks for your help. Both of you...
Brian

Re: Reshaping Zones

Jacek — Sat, 24 Feb 2007 02:53:53 GMT

Ha!
I just spent over an hour trying to figure out how to adjust my Zone and the answer was here all this time. It pays to 'Search' the forum.
One forgets what a valuable resource it is.
Thank you Chazz and Melisa.

Re: Reshaping Zones

Link — Mon, 26 Feb 2007 06:42:02 GMT

Chazz wrote:
If the zone shape was auto generated by clicking in a room, it is linked to that room. The only way to resize it is to move the walls and run a zone update. However, if you change the geometry method to manual (see below) the zone becomes editable using the standard polygon metaphors.

I'm thinking this must be an isolated case, as it goes against the polygon pet palette editing throughout all of ArchiCAD's elements. I've never found that a zone is linked to anything and they should be editable no matter what gemotry method is used.

Are you certain about this Chazz? I would like to see a module of it for my own educational purposes if you are.

Cheers,
Link.

Re: Reshaping Zones

Chazz — Mon, 26 Feb 2007 13:33:19 GMT

Link wrote:
I've never found that a zone is linked to anything and they should be editable no matter what gemotry method is used.

This was my memory as well: ALL Pollys could be edited, Zones included. However I ran up against the exact same condition as the poster described shortly before I read it and assumed it was a new behavior in AC10. I'm not in front of my workstation at the moment but are you saying you have been able to edit auto-generated zones out of the box? I will Test ASAP.

--Chazz

Re: Reshaping Zones

TomWaltz — Mon, 26 Feb 2007 13:53:31 GMT

I've found you can change a Zone's shape manually no matter how is was drawn originally.

Re: Reshaping Zones

Link — Mon, 26 Feb 2007 21:14:24 GMT

Chazz wrote:
... are you saying you have been able to edit auto-generated zones out of the box? I will Test ASAP.

--Chazz

Yes - that's what I'm saying! Sounds like you're going to get a lot of use out of it!

Cheers,
Link.

Re: Reshaping Zones

Laura Yanoviak — Wed, 15 Aug 2007 19:56:04 GMT

Melisa wrote:
Hi Brian,
It sounds like you need to adjust the settings in your Model View Options to make the adjustments and then set them back.

Go to Document / Model View Options /
Verify which one you are using and on the very bottom right corner set the background fill of the Zone to display.

Pleasant discovery: in AC11, you can edit the Zone even without it's background fill displayed.