topic elevation settings not working in A11 in Modeling

elevation settings not working in A11

Anonymous — Wed, 04 Jul 2007 16:22:32 GMT

usually in A9 and A10 i set up my 2D elevations so the outlines of the walls and roofs of buildings are in a thicker (say 0.35mm) black line, and the hatching of these walls i set to 0.18 grey line.

in A11 it doesnt seem to let me do this, all i can do is have the whole elevation coloured (but i need black and white drawings) or in B/W i can only have every pen on the elevation the same thickness

Re: elevation settings not working in A11

Anonymous — Wed, 04 Jul 2007 16:57:50 GMT

how did u do that in AC10 or 9 ?

Re: elevation settings not working in A11

Rod Jurich — Thu, 05 Jul 2007 01:29:35 GMT

percybigun wrote:
/......
in A11 it doesnt seem to let me do this,/.......

Check your Model Display settings.
And do you have your Floor Plan Display setting to show composite correctly.

Re: elevation settings not working in A11

Anonymous — Thu, 05 Jul 2007 11:41:09 GMT

where would i find display settings and floor plan display settings? this is the problem with the archicad help within the program itself, it says how to do things but doesnt say where they are located.

Re: elevation settings not working in A11

Anonymous — Thu, 05 Jul 2007 11:55:15 GMT

i cant beleive archicad have dropped this facility from the program so now i am gonna have to physically go round and draw all the lines in manually to thicken it up. this is the last time i use A11, i'm going straight back onto A10 after this model!

Re: elevation settings not working in A11

Anonymous — Thu, 05 Jul 2007 12:59:21 GMT

percybigun wrote:
i cant beleive archicad have dropped this facility from the program so now i am gonna have to physically go round and draw all the lines in manually to thicken it up. this is the last time i use A11, i'm going straight back onto A10 after this model!

ok calm down my friend

just explain to me how u used to do that in AC10 , and i hope i can help you...

Re: elevation settings not working in A11

Anonymous — Thu, 05 Jul 2007 13:36:57 GMT

percybigun wrote:
usually in A9 and A10 i set up my 2D elevations so the outlines of the walls and roofs of buildings are in a thicker (say 0.35mm) black line, and the hatching of these walls i set to 0.18 grey line.

in A11 it doesnt seem to let me do this, all i can do is have the whole elevation coloured (but i need black and white drawings) or in B/W i can only have every pen on the elevation the same thickness

Surely this is controlled by a combination of the outline pen colour setting in the individual elements, and the appropriate pen set that has that particular pen number mapped to a specific thickness and colour - exactly the same way in AC10. (Although set out in more of a tablular form than previous versions.)

Make sure you haven't got 'Uniform pen colour of uncut contours' ticked under 'Model Display' in the elevation settings.

ArchiCAD cannot and never has been able to do this automaticly, it is something you have to set up yourself by assigning the correct pen weights etc beforehand.

Hope that helps!

Pete.

Re: elevation settings not working in A11

Anonymous — Thu, 05 Jul 2007 14:41:39 GMT

i used to do it in 9 and 10 by setting all wall outlines to 0.35, then in section settings i would tick "cut elements own pen colours", and in model elements all i ticked was vectorial 3d hatching, and it worked.

just think i have sussed it, i had to go into material settings and change the vectorial hatching element pen to number 8 (0.13)

Re: elevation settings not working in A11

Anonymous — Thu, 05 Jul 2007 17:20:44 GMT

percybigun wrote:
i used to do it in 9 and 10 by setting all wall outlines to 0.35, then in section settings i would tick "cut elements own pen colours", and in model elements all i ticked was vectorial 3d hatching, and it worked.

Don't forget ticking "cut elements own pen colours" would, as the wording suggests, only effect the cut elements, not the uncut elements which is what you were having trouble with. I assume you would have had 'Uniform pen colour of uncut elements' unticked in model effects in AC10 for it to print the way you required.

I'm glad you sorted it anyway!!