topic Re: Valley Beam Dimensions in Modeling

Valley Beam Dimensions

Anonymous — Tue, 23 May 2023 14:54:03 GMT

I have am object that I am using for a valley beam, It has quite a compound rotation, and compound miters associated to it. I need to dimension this part accurately, so our field assembly crew can cut it correctly and get it into place. I am trying to figure a good way to do this. Each face of the beam is slanted, so a section is out. I want to get a dimensionally accurate look at each face of the beam. If anyone can help me out it would be appreciated!

Re: Valley Beam Dimensions

Anonymous — Thu, 06 Aug 2009 22:04:41 GMT

It would probably be helpful if you posted an image of it.

Re: Valley Beam Dimensions

Anonymous — Thu, 06 Aug 2009 22:11:39 GMT

Attached is a pdf of the roof beams. The ones in question are the two 5 1/8" x 10.5" Glue lam beams.

Re: Valley Beam Dimensions

Anonymous — Thu, 06 Aug 2009 23:06:57 GMT

Hi Brandon
Sorry I don't know how to do that in AC. Someone else may.
However, as a builder, given that problem, I'd cut two short test pieces at half the angle (a left and right) (and the full rake) of the two angle valley beams, and then I'd pull a field line measurement. HTMS.

In another thought
In AC could you not show a top view for the valley angle, and a side view to get the rake angle?
Then it's just a compound set up cut?
Sorry if this doesn't help much.

Re: Valley Beam Dimensions

Steve Jepson — Fri, 07 Aug 2009 02:27:54 GMT

Use the SEO, trun off the layer of your operator (ridge beam) and use the look to perpendicular tool on the surface you want to view flat on.
Copy and paste if you like to dimension it in plan view or save it as a 3D document and use 3D dimensions.

Shot at 2009-08-06

Re: Valley Beam Dimensions

Barry Kelly — Fri, 07 Aug 2009 02:37:22 GMT

Brandon wrote:
I have am object that I am using for a valley beam, It has quite a compound rotation, and compound miters associated to it. I need to dimension this part accurately, so our field assembly crew can cut it correctly and get it into place. I am trying to figure a good way to do this. Each face of the beam is slanted, so a section is out. I want to get a dimensionally accurate look at each face of the beam. If anyone can help me out it would be appreciated!

I think the 3D Document feature of Archicad 12 will be your friend here.
You can create the 3D view and then dimension to any surface plane that you wish (not just vertical and horizontal).

Barry.

Re: Valley Beam Dimensions

Anonymous — Fri, 07 Aug 2009 19:00:50 GMT

Is this what you want to do ?
See attachment.
Peter Devlin

Re: Valley Beam Dimensions

Anonymous — Fri, 07 Aug 2009 19:40:45 GMT

I think that the idea of finding a 3D view of the object and getting a 3D document from it and using the dimension tool is going to be the best way to go. The hard part is in essence rotated in several directions, the direction of the valley, the angle of the valley, and the angle of the roof miter. - I'll give it a try, I'm just glad I didn't have to try this in v6.5.

Re: Valley Beam Dimensions

Anonymous — Fri, 07 Aug 2009 20:00:25 GMT

Next question, how do you make an angle dimension in a 3D document?

Re: Valley Beam Dimensions

Erika Epstein — Fri, 07 Aug 2009 23:53:28 GMT

Interesting. I don't think you can dimension angles or arcs in the 3D Documents. These types of dimension tools are grayed out.

Thanks for pointing this out.
If someone can't point out how to do this then you should make a wish for this.

Re: Valley Beam Dimensions

Geof Gainer — Fri, 11 Jun 2010 21:12:45 GMT

Have you made that wish yet? I want to vote "Important"... and it will become more so the more we communicate with contractors and engineers in 3D!