https://community.graphisoft.com/t5/Documentation/printing-issue-and-Publisher-driver/m-p/125169#M19772 <DIV class="actalk-migrated-content"><T>i've had particular problems with one v12 project file where publishing the layouts to pdf results in approximately 2 - 3 cm of the right hand side of the drawing being 'trimmed' (i.e. half to titleblock and legends cut off).<BR /> <BR /> it would make sense that there's an incorrect setting relating to page margins, but despite looking everywhere i can think of, settings appear correct but problem keeps occurring. as a short term workaround i've been printing to a A0 size pdf page and then cropping it in bluebeam.<BR /> <BR /> the strange aspect is that, despite the cut-off, publishing two layouts to a combined pdf takes approx. 15 seconds and results in a 6.5Mb file (which considering the amount of 2d/fill content is reasonable). If i try and print the layouts individually, the process can take literally hours (i left it going overnight a couple of times) and result in file sizes in the 100s of Mb. This using both the amyuni driver and blubeam driver that we have installed. stranger still.<BR /> <BR /> today i opened the file in v13, with no further adjustments to settings and it published perfectly (no cut-offs, quickly, reasonable file size) while still having same issues if i try printing printing.<BR /> <BR /> i have two questions: 1) is it possible to specify an alternative pdf driver to the Publisher (rather that the standard amyuni driver) and 2) any ideas what could be causing these issues?</T></DIV> Fri, 19 May 2023 20:18:31 GMT Anonymous 2023-05-19T20:18:31Z https://community.graphisoft.com/t5/Documentation/printing-issue-and-Publisher-driver/m-p/125169#M19772 <DIV class="actalk-migrated-content"><T>i've had particular problems with one v12 project file where publishing the layouts to pdf results in approximately 2 - 3 cm of the right hand side of the drawing being 'trimmed' (i.e. half to titleblock and legends cut off).<BR /> <BR /> it would make sense that there's an incorrect setting relating to page margins, but despite looking everywhere i can think of, settings appear correct but problem keeps occurring. as a short term workaround i've been printing to a A0 size pdf page and then cropping it in bluebeam.<BR /> <BR /> the strange aspect is that, despite the cut-off, publishing two layouts to a combined pdf takes approx. 15 seconds and results in a 6.5Mb file (which considering the amount of 2d/fill content is reasonable). If i try and print the layouts individually, the process can take literally hours (i left it going overnight a couple of times) and result in file sizes in the 100s of Mb. This using both the amyuni driver and blubeam driver that we have installed. stranger still.<BR /> <BR /> today i opened the file in v13, with no further adjustments to settings and it published perfectly (no cut-offs, quickly, reasonable file size) while still having same issues if i try printing printing.<BR /> <BR /> i have two questions: 1) is it possible to specify an alternative pdf driver to the Publisher (rather that the standard amyuni driver) and 2) any ideas what could be causing these issues?</T></DIV> Fri, 19 May 2023 20:18:31 GMT https://community.graphisoft.com/t5/Documentation/printing-issue-and-Publisher-driver/m-p/125169#M19772 Anonymous 2023-05-19T20:18:31Z https://community.graphisoft.com/t5/Documentation/printing-issue-and-Publisher-driver/m-p/125170#M19773 Are you checking the Arc Resolution, at PDF Options in the Document Options Window! If the resolution is high, just lower it a bit! Thu, 31 Dec 2009 13:05:20 GMT https://community.graphisoft.com/t5/Documentation/printing-issue-and-Publisher-driver/m-p/125170#M19773 Anonymous 2009-12-31T13:05:20Z