topic Re: Dead Line Help: Publishing in PM to DWG, Lost Title Bloc in Documentation

Dead Line Help: Publishing in PM to DWG, Lost Title Block...

Anonymous — Thu, 25 May 2023 22:15:40 GMT

I am reposting this again,
Hi,
I just tried to publish my PM drawings to DWG, when I open the DWG's in AC to check for correct translation I do not see my title block or how I cropped the plans in PM. But it prints fine from PM. Where am I going wrong?
Thanks,
Joseph Harouni

Re: Dead Line Help: Publishing in PM to DWG, Lost Title Bloc

Anonymous — Wed, 29 Sep 2004 16:58:57 GMT

joseph-

plotmaker entities go into AutoCAD's paper space. this is where your titleblock is. at the autocad commandline, type "ps" or "tilemode=0" or use the menus to select a paperspace view of your model. my guess is that AutoCAD opened the file in model space.

hth
wes

Re: Dead Line Help: Publishing in PM to DWG, Lost Title Bloc

Anonymous — Wed, 29 Sep 2004 17:09:25 GMT

Weston wrote:
joseph-
at the autocad commandline, type "ps" or "tilemode=0" or use the menus to select a paperspace view of your model. my guess is that AutoCAD opened the file in model space.

hth
wes

Thanks for the reply, I am trying to check to see if the file translated correctly by opening it in ArchiCad. I do not have AutoCad, I would like to check it before sending it to the client. Can paper space be viewed in ArchCad? Should Be!
Thanks,
Joseph

Re: Dead Line Help: Publishing in PM to DWG, Lost Title Bloc

Steve Jepson — Wed, 29 Sep 2004 17:23:32 GMT

wes
Thanks for the reply, I am trying to check to see if the file translated correctly by opening it in ArchiCad...Joseph

Do you have a .dwg viewer like VoloView?

Re: Dead Line Help: Publishing in PM to DWG, Lost Title Bloc

Anonymous — Wed, 29 Sep 2004 17:30:53 GMT

Steve wrote:
wes

Thanks for the reply, I am trying to check to see if the file translated correctly by opening it in ArchiCad...Joseph

Do you have a .dwg viewer like VoloView?
No I do not, does AC9 have the capability of showing the paper space?
Thanks,
Joseph

Re: Dead Line Help: Publishing in PM to DWG, Lost Title Bloc

Anonymous — Wed, 29 Sep 2004 17:43:55 GMT

8.1 can view paper space.
Open any drawing or a blank document and set the floor plan scale at 1 to 1. Select and open the DWG. In the translator, under the "Settings in Selected Translator" section, select "Open Options" and you will see the options under Import Drawing Data From. Select "Paper space with Viewport Contents" and open. The drawing will then open in "Paper Space" with the sizes in the drawing at a 1 to 1 scale with the plot sheet for your review.

Hope this helps.

Re: Dead Line Help: Publishing in PM to DWG, Lost Title Bloc

Steve Jepson — Wed, 29 Sep 2004 17:47:43 GMT

yes

Re: Dead Line Help: Publishing in PM to DWG, Lost Title Bloc

Anonymous — Wed, 29 Sep 2004 18:25:55 GMT

tprokop wrote:
8.1 can view paper space.
Open any drawing or a blank document and set the floor plan scale at 1 to 1. Select and open the DWG. In the translator, under the "Settings in Selected Translator" section, select "Open Options" and you will see the options under Import Drawing Data From. Select "Paper space with Viewport Contents" and open. The drawing will then open in "Paper Space" with the sizes in the drawing at a 1 to 1 scale with the plot sheet for your review.

Hope this helps.

Thanks Family,
It worked but intresting enough not with merge comand & also with 1:1 canot see the text but with 1/4" = 1' 0" I see the text but the walls do not measure correct? Just do not understand DWG!?
Thanks,
Joseph