modeling at rim of floor, edge of roof

Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
‎2008-10-01
09:26 PM
- last edited on
‎2023-05-23
03:08 PM
by
Rubia Torres
‎2008-10-01
09:26 PM
Claire Remsberg
Remsberg Architecture, P.A.
MacBook Pro, OSX 12.6, ArchiCAD v25 (5010)
Remsberg Architecture, P.A.
MacBook Pro, OSX 12.6, ArchiCAD v25 (5010)
4 REPLIES 4

Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
‎2008-10-01 09:36 PM
‎2008-10-01
09:36 PM
Specific examples would be helpful. 2D or 3D is depending on the situation. For instance, we don't model studs but insert 2D Objects where needed in the wall sections. Parapet coping, eaves and rakes we model with Complex Profiles. Corrugated metal siding we would not model; unless it was useful to the condition under consideration.
MacBook Pro Apple M2 Max, 96 GB of RAM
AC27 US (5003) on Mac OS Ventura 13.6.2
Started on AC4.0 in 91/92/93; full-time user since AC8.1 in 2004
AC27 US (5003) on Mac OS Ventura 13.6.2
Started on AC4.0 in 91/92/93; full-time user since AC8.1 in 2004
Anonymous
Not applicable
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
‎2008-10-02 02:27 PM
‎2008-10-02
02:27 PM
Laura, how are you handling the corner of a raked end and the flat eave.
We have been using the Eave maker object for some time now. I tried using the complex profiles the other day and couldn't get that corner to join correctly. I did this using the beam tool.
We have been using the Eave maker object for some time now. I tried using the complex profiles the other day and couldn't get that corner to join correctly. I did this using the beam tool.
Anonymous
Not applicable
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
‎2008-10-02 03:21 PM
‎2008-10-02
03:21 PM
cremsberg, i hijacked your thread and never offered suggestions, sorry!!
I would suggest using the joist beam object under 06 Wood-Plastic. it willl give you the options of a few different section cut displays. You may be limited by pens as far as display goes.
As for modeling the exterior, you could draw a short wall using the same material so it will blend or start your upper wall "below" the current story lheight to match
I would suggest using the joist beam object under 06 Wood-Plastic. it willl give you the options of a few different section cut displays. You may be limited by pens as far as display goes.
As for modeling the exterior, you could draw a short wall using the same material so it will blend or start your upper wall "below" the current story lheight to match

Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
‎2008-10-03 06:25 PM
‎2008-10-03
06:25 PM
Chris wrote:Well -- that's sort of hit-or-miss -- and usually results in resorting to SEOs.
Laura, how are you handling the corner of a raked end and the flat eave.
MacBook Pro Apple M2 Max, 96 GB of RAM
AC27 US (5003) on Mac OS Ventura 13.6.2
Started on AC4.0 in 91/92/93; full-time user since AC8.1 in 2004
AC27 US (5003) on Mac OS Ventura 13.6.2
Started on AC4.0 in 91/92/93; full-time user since AC8.1 in 2004