Rise and Run in stair label
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
2019-01-30 06:57 PM
2019-01-30
06:57 PM
I have received compaints about the use of this word -- is it possible to change "going" to "run"
by just doing a search and replace in the script of the stair label ?
Thanks,. Randy
ArchiCAD 4.5 --- 27 , Win 10 , dual monitors, 64 gb ram,Nvidia GeforceRTX 2080 TI, I-9
7 REPLIES 7
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
2019-01-30 07:13 PM
2019-01-30
07:13 PM
Randy, doesn't the label give you the option of giving your own term to the label? seems to me I've been able to not have to use the word going.
Think Like a Spec Writer
AC4.55 through 27 / USA AC27-6000 USA
Rhino 8 Mac
MacOS 14.6.1
AC4.55 through 27 / USA AC27-6000 USA
Rhino 8 Mac
MacOS 14.6.1
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
2019-01-30 10:08 PM
2019-01-30
10:08 PM
HI Aaron , I cannot find anywhere that I can change the wording and looking at the script it not a parameter
I wondeer if they use the word "going" in the united states ? nobody here seems to of heard of it around here.
Randy
I wondeer if they use the word "going" in the united states ? nobody here seems to of heard of it around here.
Randy
ArchiCAD 4.5 --- 27 , Win 10 , dual monitors, 64 gb ram,Nvidia GeforceRTX 2080 TI, I-9
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
2019-01-30 10:25 PM
2019-01-30
10:25 PM
Same library part --- Stair Dimension Label 22 --
another problem - it is taking up too much real estate on the page How can I shrink the area between Id and dimension ?
another problem - it is taking up too much real estate on the page How can I shrink the area between Id and dimension ?
ArchiCAD 4.5 --- 27 , Win 10 , dual monitors, 64 gb ram,Nvidia GeforceRTX 2080 TI, I-9
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
2019-01-30 10:29 PM
2019-01-30
10:29 PM
there are two places: for plan labeling, and for the stair label
Think Like a Spec Writer
AC4.55 through 27 / USA AC27-6000 USA
Rhino 8 Mac
MacOS 14.6.1
AC4.55 through 27 / USA AC27-6000 USA
Rhino 8 Mac
MacOS 14.6.1
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
2019-01-30 10:49 PM
2019-01-30
10:49 PM
label tool didn't upload.
Think Like a Spec Writer
AC4.55 through 27 / USA AC27-6000 USA
Rhino 8 Mac
MacOS 14.6.1
AC4.55 through 27 / USA AC27-6000 USA
Rhino 8 Mac
MacOS 14.6.1
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
2019-01-31 03:57 PM
2019-01-31
03:57 PM
Thanks for the help Aaron -- It takes a bit of time to go thru each library part to find the correct settings - I should of spent longer but time is often at a premium .
You would think Graphisoft would change some of those wordings on the North America Library to terms that we use.
I found the answer to my last question -- I needed to check the "uniform formatting" box - I am including a screenshot for anyone else that may have trouble finding it. -- Thanks Again.
You would think Graphisoft would change some of those wordings on the North America Library to terms that we use.
I found the answer to my last question -- I needed to check the "uniform formatting" box - I am including a screenshot for anyone else that may have trouble finding it. -- Thanks Again.
ArchiCAD 4.5 --- 27 , Win 10 , dual monitors, 64 gb ram,Nvidia GeforceRTX 2080 TI, I-9
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
2019-01-31 04:16 PM
2019-01-31
04:16 PM
Hi,
It's in Master Script.
It's in Master Script.
dim stDimContent[5] stDimContent[1] = `None` stDimContent[2] = `Stair Width` stDimContent[3] = `Riser Height` stDimContent[4] = `Going Depth` stDimContent[5] = `Number of Risers`
Archicad 26, Windows 10, Corei7 3.4 GHz, 16 GB Ram.
https://www.indigofigs.com
https://www.facebook.com/indigofigs
https://www.indigofigs.com
https://www.facebook.com/indigofigs