Wall W/ Custom Profile Doesn't Like Windows or Doors
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
‎2006-06-17
08:17 PM
- last edited on
‎2023-05-26
11:39 AM
by
Rubia Torres
I am not able to put windows and doors into them without being informed that there are scripting errors.
It happens with the custom wall profiles provided by Graphisoft as well.
The window is there in 3D ok. 2D shows up a bit strange. If I attempt to mess with the window I get scripting error alerts all over.
Is there something simple I am missing before I wander any deeper into this?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
‎2006-06-20 05:41 PM
(I had dreams of super customizable profiles w/ custom pensets for sections with top plates, other details etc. Moldings and water tables and changes in sidings and stemwalls w/ footings and sill plates and A.B.'s and on and on and.... Oh my broken heart...)I too had great expectations which are being shattered by the minute. One thing I did like is that you can change the material for each "piece" by bringing up the pet palett on any edge and apply material to all edges. That is neat. However, I am having the same problems with my windows/doors. I have made a half round stacked log profile on the exerior of a 1/2" sheathing, 2x6 wall, 1.2" gypsum and my windows/doors are acting exactly how yours are. I get the blue dot of death. I have posted my problem in "other problems" thread so between the two maybe we can find a solution. I will let you know if I find the exact issue here. Good luck!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
‎2006-06-20 05:52 PM
I was feeling a bit out of my mind over this. Can't seem to not have it happen with custom profile.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
‎2006-06-21 06:40 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
‎2006-06-21 04:10 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
‎2006-06-22 05:45 PM

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
‎2006-06-23 12:02 AM
Geoff Briggs
I & I Design, Seattle, USA
AC7-28, M1 Mac, OS 15.x
Graphisoft Insider's Panel, Beta Tester

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
‎2006-06-25 05:19 AM
ArchiCAD since 4.55 ... 1995
HP Omen
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
‎2006-08-09 12:12 AM
Getting back to this. No the problem doesn't seem linked to polygon cleanliness. Even just two polygons in the profile cause problems if they are run continuous vertically as in a polygon for stud and one for sheathing. It doesn't happen when the polygons are stacked simply...
I am attaching a mod file. I hope it works. I can find no way to work around this issue. If I change the window/door setting from symbolic to projected the windows become visible again but are no longer symbolic for floor plan. They are always there in 3d (whole other array of problems there...)
I was really hoping to use this custom profile tool extensively. I am most disappointed in not being able to use it with library doors and windows. I have been using it quite enjoyably and successfully for applications not needing windows or doors.
Anyone find a working solution or is this a dead end bug?
Thanks
And I have been contacted by a tech and am assuming that this is the proper place to post this file.?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
‎2006-08-09 02:32 PM

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
‎2006-08-09 02:44 PM